How do I reset my Hayward salt Cell?

How do I reset my Hayward Aqua Rite 900?

With the pump running, take the power switch down to the “Off” position, and then back up to “Auto”. You should hear a click within 10 or 15 seconds. When you do, press the diagnostic button five times in a row. The system will go through a recalibration process.

How do I reset my salt water system?

How do I reset my Hayward salt Cell Aqua Plus?

Turn the filter pump on. You must reset the system by entering the ‘Diagnostic Menu’ and then hitting the right arrow key once and then pushing the plus key once. This should reset the light and message.

How do you troubleshoot a Hayward Aqua Rite?

How do I program my Hayward salt?

How do I program my Aqua Rite chlorine generator?

How do you unlock the configuration menu on Hayward Aqua Plus?

Press the ‘Menu’ until, ‘Configuration Menu-Locked’ appears. To unlock, press and hold the (<) & (>) until the text, on the display, changes from ‘Locked’ to ‘Unlocked’ (unit will beep).

How do I know if my Hayward salt Cell is working?

What should my Hayward salt generator be set at?

The ideal salt level is between 2700-3400 ppm (parts per million) with 3200 ppm being optimal. If the level is low, determine the number of gallons in the pool and add salt according to the chart on page 4. A low salt level will reduce the efficiency of the Aqua Rite® and result in low chlorine production.

What should my Hayward chlorinator be set at?

How much salt does the system require? Salt Systems work best with approximately 3200 parts per million (ppm) of salt, which is roughly the equivalent to a teaspoon of salt per gallon. However, all Hayward Salt Systems are designed to operate with salt levels anywhere from 2700 ppm to 3400 ppm.

How do you turn on a chlorinator on Hayward?

What temperature does a Hayward salt Cell stop working?

In pool water temperatures that are 60 degrees or below, the salt generators simply shut down and by design do not allow the salt cell to ionize (breakdown) the salt and convert it to chlorine.

What percentage should my salt cell be set at?

We suggest you start your salt chlorine generator at 50 percent output and run it for a couple of days, then check the chlorine level. In a balanced pool, a good chlorine level is 1-3 parts per million. If your chlorine levels are low, you can raise the percentage, and if it’s high you can lower the percentage.

What should my chlorinator read?

On a Hayward Salt Chlorinator, your salt reading should be between 2,700 – 3,400 PPM (parts per million) with the optimum level of 3,200 PPM.

How do you reset a T 15 salt cell?

To reset, move the switch to ‘Off’ and then back to ‘Auto’. Wait for the relay to click (5 to 10 seconds). When the instant salt level is stable (and the negative sign still present), slide switch to ‘Super Chlorinate’ and back to ‘Auto’. It takes about 30 seconds for the unit to settle back on the default reading.

How do you winterize a salt generator?

How long should I run my salt chlorinator in winter?

Reduce filter-running times: The pool’s filter should operate 3-4 hours each day during winter. If you’re using a timer, adjust it to suit. You can save money by switching the filter on during off-peak periods.

Why is my salt generator not working?

The saltwater chlorinator needs a sufficient flow of water for effective operation. A dirty skimmer basket, clogged or dirty filter, and a clogged pump strainer, can cause insufficient water flow for the chlorinator to produce less chlorine.

Why is my salt cell light blinking?

If the “Inspect Cell” light flashes by itself it is an early indication that the salt generator needs a manual reset. Each cell is equipped with 500 operational hours and requires a manual reset once it expires.

How do you change the salt reading on Aqua Rite?

To change the default reading back to the average salt, start by pressing the ‘Diagnostics’ button two times. Continue moving the switch up to ‘Super Chlorinate’ and back to ‘Auto’ until the display reads ‘AL-0’. It takes about 30 seconds for the unit to settle back on the default reading.

Why is my Hayward chlorinator not working?

The Chlorinator Has an Air Lock

An air lock inside the chlorinator can also reduce flow and chlorination. To clear an air lock, remove the lid, then turn on the pump and allow the chlorinator to fill with water. Turn off the pump; replace the lid, and turn the pump back on again.