What is a bulkhead in construction terms?

Definition of bulkhead

1 : an upright partition separating compartments. 2 : a structure or partition to resist pressure or to shut off water, fire, or gas. 3 : a retaining wall along a waterfront. 4 : a projecting framework with a sloping door giving access to a cellar stairway or a shaft.

What is another word for a bulkhead?

In this page you can discover 16 synonyms, antonyms, idiomatic expressions, and related words for bulkhead, like: transom, fuselage, coaming, sponson, crankcase, cross-member, baseboard, keelson, gunwale, gangway and bridge deck.

Why do they call it a bulkhead?

During the 15th century sailors and builders in Europe realized that walls within a vessel would prevent cargo from shifting during passage. In shipbuilding, any vertical panel was called a head. So walls installed abeam (side-to-side) in a vessel’s hull were called “bulkheads”.

What is a synonym for intrude?

chisel (in), encroach, infringe, invade, trespass.

What is a synonym for ornithopter?

Definitions of ornithopter. heavier-than-air craft that is propelled by the flapping of wings. synonyms: orthopter. type of: heavier-than-air craft.

What is a bulkhead in ceiling?

A bulkhead ceiling is a section of ceiling in an interior space that has been dropped (suspended) and boxed-in or enclosed. It is possible to find them installed in both commercial and high-end residential properties, though they may also be fitted as part of a home renovation project in smaller domestic properties.

What are false bulkheads?

The false bulkhead is the apparent back of the engine compartment. In fact, though, the panel that runs the width of the engine compartment can be removed after removing just two screws (and a couple of other things).

How are bulkheads built?

Bulkheads are normally constructed in the form of a vertical wall built in concrete, stone, steel or timber. The concrete, steel or timber walls can be piled and anchored walls, whereas the concrete and stone walls can also be constructed as gravity walls. A typical design of a bulkhead seawall is shown in Fig.

What is the space between cabinets and ceiling called?

Soffit
The space between kitchen cabinets and the ceiling is called “Soffit”. A kitchen soffit is specifically a boxy shape designed to cover up pipes, wiring, and other mechanical or to fill the gap between the top cabinets and the ceiling.

Why are bulkheads used in houses?

Traditionally, bulkheads have been used for functional purposes — concealing services like wires and pipes, projecting air conditioning and masking changes in ceiling heights (more so after renovations).

Why do bathrooms have bulkheads?

They do serve a purpose, typically it is to hide pipes, ductwork, and electrical. I find that, most of the time, they are empty or filled with insulation, if it’s on your upper level. Once the demolition is done and the space is inspected, it can then be determined whether or not the bulkhead can be removed.

What is class A bulkhead?

Class-A Panel: All watertight bulkheads are Class-A type. Bulkheads of Class A must be constructed of steel or equivalent material and should pass the standard fire test, preventing the passage of fire or smoke to the unaffected side for at least one hour.

What is a bulkhead on a vehicle?

A bulkhead is a secure, snuggly-fitting partition. It should be constructed to fit tightly against the bottom, sides, and top of the van. The bulkhead is located behind the driver and passenger seats in a van, and separates them from the cargo area.

What is the difference between bulkheads and baffles?

The baffles help to control the forward and backward liquid surge. Baffles divide the main tank into smaller tanks, and bulkheads just slow the flow of liquid to prevent liquid surge.

What is a bulkhead in a bathroom?

A bulkhead is a section of ceiling that has been dropped and boxed-in or enclosed. It’s not uncommon to have bulkheads in your kitchen, bathroom or basement. Clients frequently ask us about bulkheads and want to understand their purpose and here’s our answer. Bulkheads are typically used to conceal something.

Whats the back of a van called?

Tailgate
Tailgate – The panel at the rear of pick-ups, dropsides and tippers which stops goods falling out of the back of the load area. On pick-ups and dropsides it is hinged at the bottom for easy loading, while on tippers it is hinged at the top so your payload can slide out.

What is the bulkhead on a truck bed?

Description. The Bulkhead Tray is a universal storage solution designed to keep loose items organized and off the floor of your truck bed.