How do I reset my Intex hot tub?

How do I reset my hot tub controls?

How do I reset my spa pump?

Is there a reset on my hot tub?

There are generally two “hard resets” in hot tubs, the GFCI, and the high limit reset. The GFCI pops if there is any type of electrical short (such as water getting into the heating element, the reset on that can be in one of three places.

Why is my hot tub control panel not working?

Bottom line is – it could be a bad spaside control panel, or it could be a bad spa control board, or a bad cable that runs between the control panel and the control board. Or it could be fuse on the circuit board or the transformer, not sending the correct power to the topside panel.

How do I clear the code on my Intex E90 Hot Tub?

If the E90 code appears after running for a while:

Check and ensure there is no debris inside the spa tub inlet and outlet grids. If there is debris inside, turn the control unit off, unscrew the spa inlet/outlet grid with a Phillip screwdriver. Clean and replace it back. Make sure the spa water is clean and sanitized.

What does error code E90 mean on Intex hot tub?

no water is flowing through the system
If alarm code E90 is displayed on the control panel, it means no water is flowing through the system.

How do you turn on a pure spa?

What does error code E95 mean on Intex hot tub?

water temperature
If alarm code E95 is shown, it means the water temperature is too high. Let the spa water cool down to 104ºF (40ºC) or below, reset the control panel information by unplug and plug back in the GFCI/RCD, and reset the GFCI/RCD to restart the system. See owner’s manual for details.

What does error code E94 mean on Intex hot tub?

the water temperature is too low
If alarm code E94 is displayed on the control panel, it means the water temperature is too low. If alarm code E94 appears, unplug and plug back in the GFCI/RCD and test the GFCI/RCD to restart the system when the spa water temperature is higher than 39ºF (4ºC). http://www.intexdevelopment.com/support/faqlist?

How long does it take for Intex Pure spa to heat up?

about 24 hours
The only downfall isn’t even with set-up per se; it’s that it takes about 24 hours to heat up. For an inflatable spa, these maintain the temperature reasonably well. When it’s cold outside, the temperature will drop a few degrees during use, but will be back to the optimal temperature by the next day.

What is error code E96 Intex hot tub?

Answer. E96 means the PureSpa is experiencing a system error. If the control panel displays this error, turn off the system and unplug it. Plug the unit back in and restart it. If the error persists, turn it off and unplug it.

How do you clean hot tub sensors?

Why is my hot tub not getting hot enough?

If the spa heater is not giving enough heat, it means a water flow problem from dirty filters or partially closed valves or clogged pumps. It could also be the spa cover allowing heat to escape.

How can I make my hot tub heat up faster?

7 Hacks to Make Your Hot Tub Heat Up Faster
  1. Leave the cover on. …
  2. Turn the jets on. …
  3. Use a thermal spa blanket. …
  4. Put a pop-up canopy tent around the tub. …
  5. Wait for a warm day. …
  6. Fill up with warm water. …
  7. Use a portable immersion heater.

Why is my inflatable hot tub not heating up?

If your spa heater won’t heat, remove and clean the filter(s) to rule out a pressure or flow rate problem in your hot tub heater. Low water level, a clogged pump impeller, closed valves, clogged pipes, or blocked spa drain covers can also cause flow issues.

Why is my hot tub water cold?

My Water Gets Hot, Cold, Hot Again

Start by cleaning your filter, checking for circulation blockages, and topping off your water if necessary. Check whether your pump turns on. Your pump has to be running in order for the spa to heat up. If the pump isn’t working, you may need to replace it.

What mode should my hot tub be in?

Economy is a good setting for those who use the hot tub daily. The drop in temperature fluctuates during the year from minor or no temperature falls in the summer, to larger drops in the coldest part of winter.

Why won’t my hot tub go above 37?

If your tub won’t heat past 37* then you have probably switched put it into low range mode. All conquest Spa models have dual temperature ranges (high and low). The arrow next to the word range on your control panel will tell you what range your hot tub is in – arrow pointing up for high and down for low.

Why is my hot tub not circulating?

When your hot tub pump barely pumps…

It’s likely your filter needs to be looked at: If you feel low volume of water coming out of your heater return, remove the spa filter, clean it, and see if flow improves. If the problem still arises, it’s time to replace the filter.

How do you fix the error code on a hot tub?

How to Troubleshoot a Hot Tub FLO Error Code
  1. Shut down the spa at the breaker.
  2. Make sure there is no debris in the water that can get sucked into the pump.
  3. Take out all of the filter(s) and set them aside.
  4. Turn spa back on at the breaker with the filters out.