How much does it cost to have logs milled?

The most stable or secure method for pricing for the mill owner is a flat, hourly rate. Rates vary from location to location and range from $65 to $105 per hour plus extra charges for travel, broken blades, etc.

How much does it cost to cut a log?

Size of the Tree

A medium-sized tree, such as a maple or elm, is 30–60 feet tall and costs between $400 and $800 to remove. A large tree like a mature oak is 60–80 feet tall and costs about $700 to $1,300 to remove. Any tree taller than 80 feet will cost around $1,000–$2,000 to remove.

Is it cheaper to have your own lumber milled?

In the end, only you can decide if milling lumber from your own property is worth it. Because every job is different, we can not tell you the actual amount of money you would save or not save. Generally, it costs 5-10% more to have your lumber milled on-site.

Is it worth it to mill your own lumber?

Milling your own lumber can produce quality material for a fraction of the price of a lumber dealer. In fact, if you purchase your own mill, like I have, you can actually make a profit off of it by selling lumber to other woodworkers and by offering to mill other people’s logs.

How much is a black walnut log worth?

Thus, a 22-inch DBH black walnut tree with one 8-foot veneer log may bring $510 (170 board feet x $3.00/ft), whereas a 26-inch DBH black walnut tree with one 8-foot veneer log may command $1300 (260 board feet x $5.00/ft).

How much are red oak logs worth?

The average stumpage price is $300/MBF, or $1,800 per acre total value. Beside above, how much do logs sell for? If a mill offers to pay you $500 per thousand for red oak grade logs. Start with the $500 and figure in the profit margin you need.

How long do logs need to dry before milling?

6 weeks to 4 months
Depending on the thickness of the lumber and where you live, weather and time of the year, it will take anywhere from 6 weeks to 4 months. Most lumber is in the 1” to 2” thickness and the time above applies to thicknesses. Drying cants, timbers, posts will take considerably longer.

How long should logs dry before being used to build?

You should seal the ends within minutes after being cut down; you should not wait hours, and definitely not days! The drying time will vary depending on the wood species and thickness of the logs, but they will take at least one to two years to dry – the longer you can leave them before you start building the better.

How long can logs sit before milling?

Some logs you may want to pull to the side and let set for a couple of years. I would pile all of the maple and sycamore for atleast a 18 month sit. You can have a year or so on the oaks. Sweet gum does not last long and hickory and ash will get a bit buggy but that to adds to it sometimes.

Is it better to cut wood wet or dry?

Wet Wood Vs Dry Wood

But wet wood is actually much easier to cut than dry wood. With dry wood lacking moisture content, more friction is created as the chainsaw chain comes into contact with the wood fibers. This friction results in the chain slowing down.

Why do lumber yards spray water on logs?

Storing logs under sprinklers or in a log pond helps prevent end checking and slows deterioration caused by insects, fungal stain, and decay. However, chemical staining can occur under wet conditions. Today, softwood logs decked in the log yard are typically protected by water sprinkling during warm weather.

Can you kiln dry whole logs?

Can you chainsaw frozen wood?

It’s not impossible to cut frozen wood with a chainsaw, but it is extremely difficult. Cutting wood requires a sharp chain and frozen wood will dull your chain. You will have to perform additional maintenance on your chainsaw in the winter months and wear protective gear in order to successfully cut frozen wood.

Should logs be dried before milling?

A: Summary: Logs should be milled for drying as soon as possible, and the ends should be sealed as soon as they are felled. A bandsaw mill will create less waste than a chainsaw mill. Logs can be sawn for grade, quarter sawn, or flitch cut.

How long should logs sit before splitting?

six months
Let the wood dry at least six months and preferably longer

The hardest lesson: firewood takes a very long time to season Most folks who split their wood and stack it in well-spaced rows find that they can dry their wood in about six months.

Why does my chainsaw chain get dull so fast?

What is this? Many chainsaw enthusiasts have noted that their blades dull faster when they’re cutting muddy wood. If the logs that you’re cutting up are muddy, then perhaps that is the sole reason why your blade is dulling too fast. It won’t be hard to notice whether the wood that you’re cutting is dirty or not.

How many times can you sharpen chainsaw chain?

Cutters can be sharpened up to 10 times or more before the chain needs replacing. If your cutters are worn unevenly after a few sharpenings, a professional can regrind them to uniform shape. If you use the same chain for a few years, then buy a new one, the new one won’t mesh smoothly with the sprocket and bar.

Does snow dull a chainsaw?

Yes, you can cut ice with your chainsaw. You don’t have to apply any mineral oil to prevent the water from pollution. To prevent the blade from rusting, you will have to look after your chainsaw.

Why do loggers run upside down bars?

Every chainsaw bar has been designed to be mounted right-side up or upside down. The reason for this is that it allows the user to extend the life of his chainsaw bar by 50%. Flipping the bar will give the heavily-used areas some relief from wear and tear.

How long should a chainsaw chain stay sharp?

A chainsaw may only need to be sharpened once a year if it is rarely used, but a tool that is frequently used will need to be sharpened regularly to ensure that the blade doesn’t get too dull. On average, a chainsaw blade will retain its sharpness for about 3 hours of actively cutting through wood.

Is it OK to cut wet wood with a chainsaw?

Can you cut wet wood with a chainsaw? Yes, you can cut the wet wood with a chainsaw. Besides, there is a misconception that wet wood can impact the chainsaw bar and chain. But actually, the damp wood will not dull the chainsaw any faster than using it on other types of wood.

What is full chisel chain?

A full chisel chain is designed for the fast cutting action. In comparison to the semi-chisel chain, this chain has square-cornered teeth which makes it more aggressive when cutting.