How do you prepare wood for Waterlox?

Lightly sand the surface with a synthetic abrasive pad (medium/maroon recommended). If sanding, lightly dampen a mop, lint-free rag or micro-fiber mop with water or regular mineral spirits1 (paint thinner) to remove dust. Allow to evaporate 30-45 minutes (until dry appearance) before applying Waterlox ORIGINAL Finish.

How many coats of Waterlox should I use?

two additional
It is recommended to apply two additional coats of Waterlox ORIGINAL Sealer/Finish or two additional coats of a Waterlox Finish overtop to fully waterproof and protect.

Should I sand between coats of Waterlox?

Sanding for adhesion purposes is not required between coats of Waterlox Original Tung oil finishes. This makes Waterlox unique and different from most surface finishes which need abrasion for inter-coat adhesion.

What is the best way to seal butcher block countertops?

Do you wipe off Waterlox?

Buff off all of the excess with a clean, lint free cloth or fresh buffing pad. The first coat will use the most product and spread rate may vary slightly. DO NOT APPLY WITH A BRUSH. DO NOT ALLOW EXCESS OIL TO DRY (WIPE OFF EXCESS).

What temperature do you apply Waterlox to?

During application of Waterlox wet-applied finishes (ORIGINAL, H2OLOX®, URETHANE or MARINE), the product, project surface and environment should be close in temperature and at least 50°F during application and at least 1-2 hours afterward. When both the product and surface are cold, they are less compatible.

How do you permanently seal a butcher block?

To seal butcher block with mineral oil, you simply apply the mineral oil generously, let it soak in, and wipe off the excess. You need to do it fairly regularly at first but then only about once a month after you’ve gotten through several applications.

Is Waterlox food Safe?

Waterlox is a superb choice for finishing wood countertops because it produces an incredibly appealing and durable surface. It is waterproof, food-safe and easy to maintain. Waterlox literally locks out water and locks in the natural beauty of wood.

How do you make butcher block countertops waterproof?

To effectively seal your butcher block with a polymerizing oil, follow this regimen:
  1. Apply a coat of oil with a soft cloth.
  2. Wait 15 minutes.
  3. Buff it in.
  4. Wait 24 hours and repeat two more times.

How do you finish an unfinished butcher block countertop?

Do you need to seal both sides of butcher block?

You will need to finish all surfaces (top, bottom and sides) of your unfinished butcher block or wide plank top with a commercial grade polyurethane or Waterlox finish. Follow manufacturer’s instructions on the polyurethane or Waterlox for finishing coats (usually three or four coats).

What happens if you dont seal butcher block?

Any moisture that is absorbed into the wood and filling the pores is that much less space that is available to the oil. This moisture is going to be absorbed unevenly. This in-turn causes the oil to absorb unevenly, thus leaving the finish splotchy.

What do you finish butcher block countertops with?

If you want to chop directly on the surface of a wood countertop then you’re going to want to use a mineral oil finish or other 100% food safe oil like butcher block wax or walnut oil to name a few.

How do you finish a rubberwood butcher block?

The butcher block MUST be sealed or finished on all surfaces within 48 HOURS of removing the shrink wrap. When sealing with mineral oil or conditioner, apply an even, liberal coat of conditioner on all surfaces and let absorb for approximately 20 minutes. Wipe off any excess with clean towel. Re-apply as necessary.

How do you finish a butcher block countertop for food?

Applying Mineral Oil

Mineral oil is pretty simple to use. Pour an excess of oil onto the butcher block and let it soak into every corner of the wood. Then let it sit and wipe off the excess.

What do you seal a butcher block cutting board with?

Butcher Block Oil, also known as cutting board oil, is a food contact safe oil to seal and protect your wooden food preparation items such as butcher block countertops and wood cutting boards.

Can you put Poly on butcher block?

Follow these steps to easily waterproof your butcher block countertops with Polyurethane: Sand the counters until they’re completely clean. Vacuum any dirt off the surface and apply a natural stain. Apply a thick coat of Polyurethane, a liquid coating that dries into a plastic.

How do you seal a butcher block with polyurethane?

Is Waterlox good for countertops?

Waterlox for Countertops

Our interior Waterlox products are great options for countertops, tabletops and vanities. They provide wood surfaces with an incredibly appealing and durable finish that is food safe after curing and waterproof (does not water spot or leave rings).

What do you treat butcher block with?

Mineral oil (sometimes called liquid paraffin) is a non-toxic, non-drying oil that’s colorless, odorless, and flavorless. Its properties prevent water absorption, which is why food-grade mineral oil is the best choice for wooden kitchen tools and butcher blocks.

Is Watco like Waterlox?

For example, Watco was (and still is) often described as thinned varnish, Waterlox was (and still is) often described as tung oil, and Deft was represented as a mystery finish, unique in that it was different from other finishes.