How do you take care of velvet antlers?

A shade tree is ideal. Cover the antlers to keep the flies off, but never use a plastic garbage bag. The plastic will turn your velvet into a ruined, smelly mess. Instead, cover the antlers with a deer meat bag to allow for air circulation without any spoilage.

How do you remove old dried velvet from antlers?

How do you clean and disinfect deer antlers?

Take some warm water and a mild detergent, like Dawn® dishwashing soap. Using some good old elbow grease, soak the antlers for a few minutes or just start scrubbing them with a wet washcloth and the soap. They should clean up nicely very quickly. Rinse them clean, and let them dry.

What do you spray velvet antlers with?

Apply VelvaLok spray liberally to all velvet surfaces – saturate the antlers until the product is dripping off the pedicles. The spray tip should be no more than 2 inches from velvet tissue.

How do you clean shed antlers?

Step 1: Cleaning the Shed Antlers

If the antlers aren’t too dirty, you can do this simply by rubbing them with a cloth. However, if the antlers are very dirty, then you’ll want to soak them in soapy water for a few minutes (Dawn dish soap works well). Then take a soft-bristled brush and gently scrub away the debris.

How do you remove stains from antlers?

Take some clean, white paper towel or cotton rag, dip it in acetone and scrub at the spots. If the cloth picks up color, turn it to a clean area and scrub again. Once you have removed all you can that way, take some white paper towel and fold it several times. Make a section big enough to cover the drip area.

How do you preserve antlers?

  1. Clean the antlers. While you are still outside, use a cloth to gently clean the dirt and debris off the antlers. …
  2. Bring the antlers inside. …
  3. Cover the antlers with a protective coating. …
  4. Soak the antlers in a solution of one part linseed oil and one part turpentine to help preserve them.

Will velvet antlers rot?

“Generally, by the first part of September velvet antlers are usually drying up, but they will still have that tissue which can rot and fall off if you don’t take care of it.”

How do you harden velvet antlers?

Do antlers need to be treated?

The horns themselves do not need to be cured or dried as they are hard bone with little moisture in them. It is the skull plate that the horns are attached to that needs to be cured and dried before the horns can be mounted.

How do you clean horns?

How long do antler sheds last?

It can take as little as 24-48 hours for the antlers to actually fall off, but the shedding process takes between two to three weeks and then new antlers will regenerate throughout the summer.

How do you refresh deer antlers?

All you need to restore them is dish soap, a paintbrush, wood stain and fine steel wool. If the antlers are chalky and porous you will also need two-part molding compound and fine sandpaper. Start by cleaning the antlers with soap and water and allow them to dry.

Can I give my dog antlers I found?

Overall, antlers are safe chews for your dog to enjoy with proper supervision. They are a cruelty-free and sustainable chew that will last your dog a long time. Elk and deer antlers are rich in protein and a natural source of many different nutrients for healthy dogs.

How do you clean deer antlers in the woods?

Place the antlers in the water, ensuring that they are fully submerged. Turn up the heat and allow the antlers to boil for approximately 15 to 30 minutes. This should be enough to loosen any caked-on dirt. Carefully remove the antlers and rub them clean with a cloth.

How do you make deer antlers shiny?

Spray the antlers with a coat of semi-gloss polyurethane to maintain the shine.

How do you make antlers Brown again?

How do you make deer antlers white?

Mix 12% hydrogen peroxide and water in a ratio in a plastic container large enough to accommodate the deer skull. You can use lower concentration depending on your preference. Soak the deer skull into the hydrogen peroxide solution making sure that the skull is completely soaked but the antlers are not.

Can you soak deer antlers in bleach?

Rust-covered deer antlers can be whitened by soaking in water plus bleach. I tend to be heavy-handed with bleach, but it won’t dissolve the bone.

What do you coat deer antlers with?

Spray a clear coat of polyurethane onto all parts of the antlers to protect them from water and insect damage. This spray also helps preserve the natural colors of the antlers.

How does hydrogen peroxide whiten antlers?

Here’s how to do it:
  1. Put the bones in your bucket.
  2. Pour in your hydrogen peroxide.
  3. Then top it with water.
  4. The bones will start foaming, which means the hydrogen peroxide is working. Hydrogen peroxide also heats up when it is working.
  5. Loosely cover the bones while they soak. …
  6. Let the bones whiten for about 24 hours.