How do I get my WYZE camera back online?

Reboot your Wyze Base Station to reestablish the connection.
  1. Unplug the base station from power, wait 5-10 seconds, then plug it back in.
  2. Once the status light is solid blue, the reboot is complete.

Where is the reset button on a Wyze Cam?

How do you reset a Wyze wireless camera
  1. Delete the camera from the App.
  2. Observe the back LED. It should change from solid blue to blinking yellow.
  3. Remove the micro SD card from the slot.
  4. Press and hold the setup button on the bottom of the camera for 10 seconds.
  5. Wait for the message “ready to connect”

How do I reset my WYZE camera to a new WiFi?

To perform a factory reset on your Wyze Plug:
  1. Press and hold the on/off button on the side of the Plug until the status light begins to flash blue.
  2. Once the status light begins to flash blue, you can setup the Wyze Plug via the app again with the new WiFi network.

Why is my Wyze Cam not connecting?

Unplug the camera’s USB cord, wait 5 seconds, and plug it back in. If you still get the error, you can try to deactivate any firewall settings on your device or network. Slow internet speeds can also cause these errors. Wyze Cam needs a minimum upload speed of 1-2 Mbps for SD and 4-7 Mbps for HD.

Can you factory reset a blink camera?

Step 1: Press and hold the reset button for 30 seconds. Step 2: The camera should now be back at its factory defaults mode.

How do I fix my WYZE camera?

Basic Troubleshooting
  1. Check that your phone or tablet is on a 2.4 GHz network. On iOS: In the Settings app, tap Wi-Fi to see your network name. …
  2. Forget all WiFi networks, restart your phone/tablet, then reconnect to your 2.4 GHz network. …
  3. Power cycle your Wyze Cam. …
  4. Force close the Wyze app, then open it again.

How do I reconnect my Wyze camera after unplugging?

Steps to Connect Wyze Cameras to New Wi-Fi

Connect your Wyze camera to the USB port or a power outlet. Wait until it flashes yellow (about thirty seconds). Hold the Setup button on the back of the camera until you hear the automated message “ready to connect.”

Why is Wyze camera flashing?

A flashing blue light means that your Wyze camera is connected to the Internet at your home. However, it also means that the Wyze camera is finishing its setup process and should be ready for use soon. Once the blue light becomes solid and steady, you are good to go.

What is error code 90 on Wyze camera?

Per Wyze’s support site, error code 90 is an internet connectivity issue that requires you to power cycle your cam. Power cycling really just means completely powering off an electronic device. Typically this requires you to disconnect it from its power source.

What happens if you unplug WYZE camera?

If you unplug your camera then plug it in again in the same WiFi environment your camera will automatically reconnect to the WiFi network. You do not need to re-enter the WiFi information again. It may take a minute or two for your camera to initialize and get connected to the network.

What happens if you unplug a camera?

When your house, the cameras won’t record. When you are away from the home, the cameras record. They’ll still be “working” but not recording.

How do you Unbrick a Wyze camera?

Hold the setup button, plug in your USB cable, and keep holding the setup button for 12-15 seconds, then release the button. Wait for 3-4 minutes. The camera will reboot and change light status during this time.

What is error code 09 on Wyze camera?

This error means that your Wyze Cam can’t be reached by the streaming servers.

Why do my Wyze cameras keep going offline?

Fix Wifi Issues with our Self-Service app

Try a factory reset, and attempt set up as a new device: Remove the SD card if there is one inserted. Hold down the setup button until the status light turns solid red. Once the status light begins flashing red, you may attempt to set up again.

How do I factory reset my WYZE Cam v2?

To factory reset your Wyze Cam v2:

With the Wyze Cam plugged into power, press and hold the setup button on the bottom of the camera for 10 seconds. This will reset the camera. Wait at least 30 seconds for the device to initiate. This process can take up to 5 minutes.

How do I format my WYZE camera SD card?

Format on a Windows computer:
  1. Remove the microSD card from the Wyze Cam.
  2. Insert the card into your computer. …
  3. Open your computer’s file browser.
  4. Right-click on the microSD card in the navigation panel. …
  5. Select “Format…” from the right-click menu.
  6. Ensure that the Format Type is set to FAT32.
  7. Click Start.

How do you fix unresponsive WYZE camera that won’t pass solid yellow light?

Solid yellow light

Check to see if you are using the power cable and wall plug that came packaged with the camera. If you are NOT using the power cable and wall plug that came with the camera, please switch to the power cable and wall plug that came with the camera to see if this resolves the issue.