The shiny side goes down when your cutting. The vinyl side goes face up. You want to cut through the vinyl, but not through the carrier sheet. Perform test cuts to get your settings correct, and remember to reverse your image on your computer before cutting HTV.
Which side of my vinyl goes down on Cricut?
Cutting Vinyl with a Cricut machine
Place vinyl liner side down onto Cricut StandardGrip Mat. Select images and size and load the mat into the machine.
What side of the vinyl goes down for iron on?
shiny side
Which side of iron-on vinyl goes down? When you are cutting iron-on, place it shiny side down on the cutting mat. When you are ironing it, you flip it over so the iron-on is shiny side up.
What is the liner side of vinyl?
shiny side
The shiny side is the liner, and the dull side is the heat activated side that you will adhere to an object. You can tell iron-on vinyl from regular vinyl by the front liner.
Do I place my vinyl shiny side down?
Which side is liner on Cricut iron-on?
side down
Place Iron-on sheet, liner side down, onto Cricut StandardGrip cutting mat. If using Smart Iron-On with Cricut Joy, it may be loaded into the machine without a mat.
How do you heat press vinyl on both sides of a shirt?
Which side of glitter vinyl goes down?
5 -Insert your HTV into your cutting machine but remember to load the shiny (glitter) side down.
Which way does vinyl go on Cricut?
Where does vinyl go on left chest?
How to Place a Left Chest Logo on a Shirt. While you have your shirt on your t-shirt heat press, simply draw an imaginary vertical and horizontal center line. For the left chest, your vertical line will be just off the side of the collar. Your horizontal line will start at the armpit seam.
How far down do you put vinyl on a shirt?
In general- adult sized shirt designs should be between 11 and 14 inches. For kids sized shirts, you only need between 5.5 and 9 inches.
How far down do you place vinyl on the back of a shirt?
Back designs should be placed using the center crease and four inches down from the center of the neckline.
Where does the vinyl go on the back of a hoodie?
Where do you put vinyl on pocket?
Pocket: Find the center point of the collar edge and make an invisible line (or use your heat press) to meet an invisible line from under the armpit. The point where these two lines intersect is the center of your pocket design. 5″ x 5″ works well on adult 2XL, 3XL, 4XL, and larger sizes for pocket HTV placement.
Where do you put vinyl on a shirt?
LEFT/RIGHT CHEST
The vertical line will start just off the side of the collar. The horizontal line will start at the armpit seam. Where these two lines meet is where the design should be placed. TIP: Do not to place the design too far to the left (or right) as it may end up in the armpit area.
Where does vinyl go on front of hoodie?
How far down do you place a decal on the back of a hoodie?
Back Center
Zip-Up / Hooded: 4–4.5″ from the bottom of the neck’s edging when hood is up.
Where do you put vinyl on a sweatshirt?
Where does a left chest logo go on hoodie?
Design Placement Tips
Jackets – Left Chest. 3.5″ to 4″ from center’s edge and 6″ to 8″ from the seam of the left shoulder.
Polo Shirts. 7.5″ to 9″ from the shoulder’s left seam and 4″ to 6″ from the center, in line with the collar meeting the shoulder seam.
Sweatshirts.
Where does a left chest logo go?
Most logos are left chest aligned allowing for a name, or a name patch to be placed on the right of the persons chest. The inside edge of the collar is used as a vertical center line for aligning the logo or design. The bottom of the logo is typically no lower than the bottom of the placket of the polo.
Which side of the shirt does a logo go on?
left
A: The most common logo placement on a shirt is on the left chest. This has become the most common placement due to the original handshake, which would force your right hand to extend and therefore cover up the right chest area and your logo.
Where does the monogram go on a sweatshirt?
Traditionally, a monogram is embroidered 6.5”- 7” down the left shoulder seam. However, I did one on the right shoulder seam that came out great! I also like to place the monogram in the center front as well (typically 3” down from the center neckline line).